-
Silver is scratch-resistant
but not scratchproof. Polish your silver jewelry
regularly using non-abrasive cleaning cloth, to
maintain the original condition of silver jewelry.
-
Soap & water
will also help keep your silver looking good. But
do not dry silver with paper towel or tissues, always
use soft cloth only.
-
When you are not
wearing your silver jewelry, store them in a cool,
dry place. Zip-luck bags or the individual cloth
pouches are ideal for this & will help prevent
both tarnishing or scratching with other pieces.
-
Never immerse
your silver jewelry in chlorine, salt water, mineral
spring, & suntan lotion. Be careful some household
cleaning lotion contains chlorine bleach, these
will cause discoloration & might help to losses
the gems stone.
-
Never use an ultrasonic
cleaner, ammonia or any chemical solution to clean
opaque gemstone, such as turquoise, malachite, onyx,
lapis lazuli & opals. They are porous stones
& they may absorb the chemicals, & cause
discoloration. Simply wipe them gently with a moist
cloth until clean.
-
To remove tarnish
or oxidation film from silver you can use fresh,
uncontaminated commercial silver dip liquid, polish
paste or polish cloth, available in jewelry suppliers
or hardware stores. Make sure there are no loose
stones or parts.
Limit the gemstone's exposure to silver
cleaners - cleaners may harm certain kinds of gemstones.
Tarnish is a product of oxidation,
caused by interacting of silver jewelry or objects
with certain elements such as oxygen or sulfur as
well as with certain acids. Tarnishing on silver jewelry,
when worn on a regular basis, usually does not occur.
Storage for a prolonged time causes silver jewelry
to tarnish.
Usually, tarnish will not appear on
jewelry that is worn on a regular basis. The gentle
frictions from wearing and contact of oils on the
skin will likely keep your jewelry bright and sparkling.
Note though that taking certain medications can cause
changes in skin acidity and may cause your jewelry
to tarnish. Contact with rubber bands may cause tarnish
- the sulfur in rubber is a catalyst for tarnish.
To keep your silver tarnish-free,
frequently clean your silver in a mild dishwashing
liquid diluted in water. Thoroughly dry your silver
jewelry after exposure to water. Store silver in a
dry container or a plastic bag with anti-tarnish paper.
It is recommended that you keep your
sterling silver in an air-tight protective bag made
of tarnish proof cloth or a plastic zip lock bag.
Although your jewelry is scratch resistant it isn't
scratch proof, so we recommend that you store your
jewelry so that it isn't rubbing up against other
articles. Also, when storing remember
that exposing it to air promotes tarnishing. Avoid
storing your Sterling Silver Jewelry directly on wood
surfaces, because wood usually contains acid that
can mar the finish.
To Summarize
Do not allow your silver to come in contact
with items containing sulfur like matches, rubber
bands, etc.
Avoid your jewelry's contact with
abrasive soaps, perfumes, sprays, dyes, etc.
To prevent tarnishing, wash jewelry with mild soap
and water, rinse, and dry thoroughly.
Store in air tight zip luck bag.
Silver is a relatively soft metal
and can scratch. Don't scrub with abrasives.
Use a jewelry polishing cloth to prevent
tarnish.
Maintain the good shape of
the bracelet, by following simple measure
Put the bracelet as shown in picture, after the bone,
in the middle part of the hand. Then slowly push &
turn. If the bracelet open too much then press the
both end part only by holding the bracelet. &
to take off apply same way. Adjust the open part of
the bracelet, & slowly turn & pull from the
arm.
A good shape Bracelet.
Never
press the bracelet, from the side, as shown, it develop
stress at 1 point, which makes the stress point hard,
& bracelet loose its shape. Doing this many times
may break the bracelet at the stress point.
To adjust the size of the bracelet for your arm, close
& open the bracelet by pressing & opening
the end part.
To
adjust the size of the bracelet for your arm, close
& open the bracelet by pressing & opening
the end part.